#Huawei mac address list software#
#Huawei mac address list mac#

#Huawei mac address list mac#

The switch load balances non-known unicast packets based on source and destination MAC addresses by defaultĬommand to modify Eth-Trunk specifications, the existing Eth-Trunk configuration will become invalid or be lost. If the enhanced mode is not used, problems such as packet loss and uneven load balancing may occur. assign trunk trunk-group 64 trunk-member 16 Suggestionsġ- When more than 128 Eth-Trunks or 16 member interfaces are configured,the enhanced mode is used for load balance known unicast packets by default. Set the maximum number of LAGs to 64 and the maximum number of member interfaces in each LAG to 16. Starting from V200R009, for the S6720EI and S6720S-EI, you can run the assign trunk * command to configure the maximum number of Eth-Trunks and maximum number of member interfaces in each Eth-Trunk. On the S6720EI and S6720S-EI, you can run assign trunk command to set the maximum number of 128 LAGs and the maximum number of 64 member interfaces in each LAG. Generally, a switch supports a fixed maximum number of LAGs and a fixed maximum number of member interfaces in each LAG.Īn Eth-Trunk contains a maximum of 32 member interfaces on the S5720HI, S5730HI, and S6720HI, 16 member interfaces on the S1720X, S1720X-E, S5730SI, S5730S-EI,S6720LI, S6720S-LI, S6720SI, and S6720S-SI, and 8 member interfaces on all other models.

#Huawei mac address list software#

Software version : VRP ® software, Version 5.170 (S6720 V200R010C00SPC600) Handling Process Indicates the VLAN of the service port with the MAC address.Ĭustomer unable to add more than 8 ports in LACP Eth-trunk.Įrror: Failed to add the port into the trunk because the members of the trunk reached the upper limit Indicates the subrack ID, slot ID, and port ID of the service port with the Indicates the type of the service port with the MAC address. Indicates the bundle ID of the service port. Port, it is the virtual channel identification. Port, it is the virtual path identification. The following table describes the parameters in response to the.The system displays the queried result when the command.Table, do as follows: huawei#display mac-address pwindex 1 To query all the MAC addresses that belong to PW index 1 in the MAC address Table, do as follows: huawei#display mac-address vlan 100Ġ - adl 00e0-fc00-0002 static 0 /3 /0 0 35 100 To query all the MAC addresses that belong to VLAN 10 in the MAC address Ppp-pppoe, ip-ipoe, ip4-ipv4oe, ip6-ipv6oe Note: F-Frame, S-Slot, P-Port, F/S/P indicates PW Index for PW,Ī-The MAC address is learned or configured on the aggregation port SRV-P BUNDLE TYPE MAC MAC TYPE F /S /P VPI VCI VLAN IDĠ - adl 00e0-fc00-1000 static 0 /3 /0 0 35 100 To query the MAC address of the ADSL port 0/3/0,ĭo as follows: huawei#display mac-address port 0/3/0 Range: varies with the board type.įor the filtering function provided by this command, the result is displayed It can be a physical port or a virtual port.Ĭurrently, only the mapping from a VLAN to an AC is supported. The attachment circuit is the connectionīetween a CE and a PE. (case sensitive), and underline (_) are allowed. It uniquely identifies a VSI.Ĭharacter string type, a string of 1-15 characters. Query the configuration of MAC addresses. Specified service port in the MAC address list, use this parameter. Indicates the MAC address of the METH port. Queries all MAC addresses in the MAC address table. To query all the static MAC addresses in the To query the MACĪddress of a specific VLAN, use this parameter. To query the MAC address of a specific port, use

Indicates the subrack ID, slot ID, and port ID. To query the MAC addresses of a specific board, use this Enter a slash (/) between the subrackĪnd slot IDs. Table after a MAC address is added to or deleted from the MAC address table, run To query the dynamic and static MAC addresses in the MAC address This command is used to query the information about the MAC address table in Dynamic MAC addresses in the MAC address table also have the agingĪssociated address items of a device that has not sent any packet for a certain MAC address and the port number of the received packet to the table as a new

Table, the MA5680T/MA5683T/MA5608T can add the source If the source MAC address of a received packet does not exist in the The MAC address table of the MA5680T/MA5683T/MA5608T is capable of learning new MACĪddresses. To meet the requirements of bearing multiple services, the MA5680T/MA5683T/ MA5608T supports the MAC address table and